Diamond taper cutter M14, 2-38 mm
    Diamond taper cutter M14, 2-38 mm
  • Out-of-Stock
  • Out-of-Stock
Diamond taper cutter M14, 2-38 mm
Diamond taper cutter M14, 2-38 mm
    Diamond taper cutter M14, 2-38 mm
    Diamond taper cutter M14, 2-38 mm

Diamond taper cutter M14, 2-38 mm

€25.21 with VAT
€25.21 without VAT
Shipping to Itella Smartpost - For free!
Used for enlarging and shaping the hole. • Suitable for granite, marble, porcelain ceramics and hard ceramics. • Suitable for both dry and wet processing. • Working speed 10000-14000 rpm. • M14 connector. • For use with angle grinders.
Quantity
Out-of-Stock

9382
5906741648493
Main | Hammers |
Itella Smartpost - For free!
DPD carrier - 4.59 EUR
• the look of the real item may be a bit beam from those in the photos;
• the product may not be in the original packaging.

You can pick up the goods free of charge at: Veiverių st. 153, LT-46417, Kaunas, Lithuania.

Delivery price depends on the weight of the product, the chosen delivery type and location. Our products can be deliver to most of the European countries. Please put an item into the basket and choose location where to deliver to see exact price*.

*The delivery price of oversized goods may be higher than when calculated by weight (eg: ladder), because one of the dimensions is over 2 meters and so on. There may also be a higher delivery cost for oversized boxes, such as a vacuum cleaner or large machine tool, where it takes up a large volume and must be transported on a pallet. In such cases, the customer is additionally warned about higher delivery costs and has the right to cancel the order, or pick up the goods by their own transport.

*Delivery to islands and less rural places are charged extra by our partners DPD.

After courier delivers parcel, inspect it carefully - the packaging must be undamaged. If you notice that the packaging of the delivered goods is damaged, you must not accept the parcel and note in the delivery and acceptance certificate which is provided by the courrier that it was damaged. Please inform us about damaged goods too by e-mail [email protected] or by phone +370 686 47 132.

Your purchased goods in Europe should reach you within 1-7 working days (weekends not included). Exact delivery times are written in the product card, where it shows if it is available from our main or second warehouse.

You can currently pay for the goods using the following payment methods:

Logo
Name
Information
Klarna
You will be directed to the Klarna payment options which are: credit/debit bank card, 4 installments, pay in 30 days, financing.
Paypal
There is an additional 3% charge for PayPal payment insurance which is taken directly by Paypal bank. This additional insurance fee is automatically added by the bank to cover the additional costs of Paypal customer service.
Bank transfer
You will need to pay according to the received pre-invoice, which we will send to you immediately after creating the order. It is important that you enter the order number in the payment destination. The details of the order will be specified in the sent e-mail.

5 other products in the same category:

  • Out-of-Stock
Specialist

Diamond drill bit D68 M14

€35.95 with VAT €35.95 without VAT
Availability: Out of stock
Diamond crown (drill bit) is designed to be used with an angle grinder. The drill bits made using the new advanced vacuum technology are characterized by durability and high efficiency. These drill bits are designed for both dry and wet drilling of especially hard materials. M14 screw fastening is intended for angle grinders. An angle grinder ensures high rotations needed for the efficient performance of the drill bit. It is an especially effective way for dry drilling of hard materials such as especially hard stone mass tiles. Service life of the drill bit can be prolonged by using water.
IRWIN HSS TURBOMAX 4.8 X 86
  • Out-of-Stock
Irwin

IRWIN HSS TURBOMAX 4.8 X 86

€4.12 with VAT €4.12 without VAT
Availability: Out of stock
Benefits: • Jet Point tip - longer lasting sharpness, does not ride on the drilling surface. • 100º sharpening angle - faster drilling, better centring, no need to apply pressure when drilling. • Special edge design - clean drilled hole, extra round hole when drilling sheet steel. The tool is used for: • For sheet steel. • For sheet steel. • Aluminum. • For non-ferrous metals. • All types of wood. • Plastic.
HSS Hex Shank Bit 2mm
  • Out-of-Stock
Stanley

HSS Hex Shank Bit 2mm

€1.71 with VAT €1.71 without VAT
Availability: Out of stock
PRECISION METAL DRILLING New structure of the drill bit head allows more precision while drilling, prevents slipping and "floating" effect. Suitable for drilling metal pipes and rough surfaces. Suitable for drilling metal sheets, mild steel and non-ferrous metals.
HSS PRO DIN 340 10.00 QUAD PK5
  • Out-of-Stock
Irwin

HSS PRO DIN 340 10.00 QUAD PK5

€21.13 with VAT €21.13 without VAT
Availability: Out of stock
DIN 340 standard drills (prolonged). 118 degree sharpening angle. Packaged in plastic packages (10-5 pcs.)
Specialist+ Cobalt drill bit 11 mm 5pcs
  • Out-of-Stock
Specialist

Specialist+ Cobalt drill bit 11 mm 5pcs

€29.98 with VAT €29.98 without VAT
Availability: Out of stock
Metal: - HSS COBALT metal, steel with 5% cobalt, less heating (drilling drilling for longer periods of time) and is stronger. Shape and construction: - Double drill sharpening. - 135° drill tip allows for straightness when drilling harder drill bits. The drill bit is designed to drill through steeper materials. - Hardened, gold surface finish for greater durability. - Professional shank machining for precision drilling and fast chip removal For fast deburring. - Set of 10 pieces for this drill. Applications: - In V2A steel drilling. - In V4A steel drilling. - In V4A cast iron drilling. - In titanium drilling. - Drilling of hard materials up to 1100 N/mm2.